Total views : 200

Thermal Design and Rating of a Shell and Tube Heat Exchanger Using a Matlab® GUI


  • Chemical Engineering Program, Research Group on Sustainable Chemical and Biochemical Processes, Universidad del Atlántico, Km 7 Antigua Vía a Puerto Colombia, Barranquilla, Colombia
  • Chemical Engineering Program, Research Group on Simulation and Process Control, Universidad del Atlántico, Km 7 Antigua Vía a Puerto Colombia, Barranquilla, Colombia
  • Mechanical Engineering Department, Research Group on Efficient Energy Management, Universidad del Atlántico, Km 7 Antigua Vía a Puerto Colombia, Barranquilla,, Colombia


Objectives: To design and rate a Shell and Tube Heat Exchanger Using a Matlab® GUI and assess it with the evaluation guide ISO/IEC 9126-1 Methods/Statistical analysis: The general procedure is initiated by estimating the heat flow, the thermal properties and some dimensionless numbers in heat transfer based on the caloric temperature for the fluids. Finally, the films and overall heat transfer coefficients were used to estimate the heat transfer area, which is needed to calculate the approximate size of the equipment, and therefore its cost, been this goal a powerful tool for engineering education. Findings: The student can see the effect of the dirt factor, the geometrical configuration, the thickness of the tubes, and the flow velocity inside or outside the tubes, etc., on the resistance of the total heat exchange between the fluids to later carry out laboratory experiences where they can compare the results and give a better explanation of the profiles obtained with the variable chosen to be studied. It can help engineering students to be more creative in finding different ways to increase the efficiency of heat exchangers or in the design of new ones. Using the program, it was determined the lowest obstruction factor to the heat transfer as a function of BWG number and external tube diameter, the correction factor of the log mean temperature difference and the Dittus and Boelter, and Sieder and Tate parameters. It was confirmed the importance of the software in the student learning process according to the software quality requirements and evaluation guide ISO/ IEC 9126-1. Application/Improvements: The GUI let students to reach the heat transfer educational objectives and the program outcomes expected for new engineers improving the communication between design engineers and technicians in industry.


Dittus and Boelter Parameters, Engineering Software Education, Graphical User Interface, Obstruction Factor, Shell and Tube Heat Exchanger

Full Text:

 |  (PDF views: 211)


  • Iancu M, Cristea MV, Agachi PS. Retrofit design of heat exchanger network of a fluid catalytic cracking plant and control based on MPC, Computers and Chemical Engineering. 2013; 49(0):205-16. Crossref.
  • Chang HM, Lim HS, Choe KH. Effect of multi-stream heat exchanger on performance of natural gas liquefaction with mixed refrigerant, Cryogenics. 2012; 52(12):642-7. Crossref.
  • Cormos CC, Cormos AM, Agachi S, Jacek Jo, Jan T. Heat and power integration for hydrogen-fuelled Combined Cycle Gas Turbine (CCGT), Computer Aided Chemical Engineering. Elsevier. 2009; 26:1239-44. Crossref.
  • Stehlik P. Heat transfer as an important subject in wastetoenergy systems, Applied Thermal Engineering. 2007; 27(10):1658-70. Crossref.
  • Yongqing W, Xin G, Ke W, Qiwu D. Numerical Investigation of Shell-Side Characteristics of H-Shape Baffle Heat Exchanger, Procedia Engineering. 2011; 18(0):53-8. Crossref.
  • Skaugen G, Gjovag GA, Neksa P, Wahl PE. Use of sophisticated heat exchanger simulation models for investigation of possible design and operational pitfalls in LNG processes, Journal of Natural Gas Science and Engineering. 2010; 2(5):235-43. Crossref.
  • Rojas M, Zeppieri S. Simulation of an industrial fixed-bed reactor with cocurrent downflow for hydrogenation of PYGAS, Catalysis Today. 2014; 220-222(0):237-47. Crossref.
  • Ibá-ez JG, Ochoa GV, Chamorro MV. Design of a mechanical subcooling system device for increasing a low temperature refrigeration system’s capacity, Prospectiva.2013; 11(2):13-20.
  • Uddin F, Tufa LD, Taqvi SA, Vellen N. Development of regression models by closed–loop identification of distillation column - A case study, Indian Journal of Science and Technology. 2017; 10(2):1-6.
  • Raju M, Kumar S. Optimization of heat exchanger designs in metal hydride based hydrogen storage systems, International Journal of Hydrogen Energy. 2012; 37(3):2767-78. Crossref.
  • Ozudogru TY, Olgun CG, Senol A. 3D numerical modeling of vertical geothermal heat exchangers, Geothermics. 2014; 51(0):312-24. Crossref.
  • Ragul G, Kalivarathan G, Jayakumar V, Maruthur P, Jacob I, Naveen Kumar S. An analytical investigation on design and structural analysis of cam shaft using solid works and ansys in automobiles, Indian Journal of Science and Technology.2016; 9(36):1-9.
  • Tlebaldiyeva M, Sadikov T, Kamiyeva G, Moldakhmetova Z. The implementation of information technologies in higher education: A case of Kazakhstan and Turkey, Journal of Theoretical and Applied Information Technology. 2016; 88(3):517-24.
  • Sugiyanto, Rochimah S, Sarwosri. The improvement of software quality model for academic websites based on multi-perspective approach, Journal of Theoretical and Applied Information Technology. 2016; 86(3):464-71.
  • Kern DQ. Process Heat Transfer: McGraw-Hill Book Company, Inc. 1950, p. 1-879.
  • ISO/IEC. Systems and software engineering-systems and software quality requirements and evaluation (SQuaRE)System and software quality models. Date accessed: 15/03/2017. Available from: ui/#iso:std:iso-iec:25010:ed-1:v1:en2011.
  • Dittus FW, Boelter. LMK. Heat transfer in automobile radiators of the tubular type. Publications in Engineering, University of California: Berkeley, 1930; 2:433.
  • Sieder EN, Tate GE. Heat Transfer and pressure drop of liquids in tubes, Industrial Engineering Chemistry. 1936; 28:1429-35. Crossref.


  • There are currently no refbacks.

Creative Commons License
This work is licensed under a Creative Commons Attribution 3.0 License.