SciresolSciresolhttps://indjst.org/author-guidelinesIndian Journal of Science and Technology0974-564510.17485/IJST/v13i1.1848Narrowband aperture coupled waveguide to microstrip transition for space applicationsRavalVidhiravalvidhi69@gmail.com1PatelAmit2PhD Scholar, Charusat University, CSPIT, ChangaAnand, Gujarat, 388421, +091-745255229IndiaAssistant Professor, Charusat University, CSPIT, ChangaAnand, Gujarat, 388421India1412021Abstract
Background/Objectives: To design, analyze and fabricate aperture coupled waveguide to microstrip transition for Ka-Band where energy is coupled through slot in ground plane and a metal patch placed over the substrate. Methods: Impedance matching approach has been adopted for transition design. Microstrip line is inserted into the waveguide through aperture acting as a probe. Followed by inductive line and transformer line for impedance translation between waveguide and microstrip line. Waveguide transition has been designed using Ansoft High Frequency Structure Simulator (HFSS) full-wave EM simulator. Findings: Designed transition shows return loss performance better than 15 dB and insertion loss better than 0.5 dB for back to back configuration over a frequency band of 34 – 36 GHz. Transition is fabricated on RT5580 Duroid substrate (∈r=2.2) with substrate thickness 0.254 mm. Measured results show return loss better than 25 dB and insertion loss less than 1 dB over a frequency band of 34-36 GHz. Table 2 shows comparison of present design with previously reported designs in terms of performance. Novelty/Applications: Comparison of the presented transition shows superior performance to previously reported transition designs in terms of transition bandwidth and insertion loss. Aperture coupled transitions can be widely used for space applications where hermetic sealing is required and it saves extra effort for sealing. Certain RF circuit applications require narrowband waveguide transitions to attain required performance, in this case aperture coupled transition can be a good option and its integration with RF circuits is also easy. Fabricated transition design results show good agreement with simulated results so it can be concluded that design is tolerant to fabrication errors. Transition has been fabricated using standard PCB process so production of such transition can be done easily without requirement of any special facility for fabrication.
In past few decades, millimeter wave frequencies have been major attraction to lot of researchers due variety of applications in various fields like detection of objects 1, remote sensing2 and astronomy 3. At millimeter and sub-millimeter wave frequencies waveguides are often used as interconnect to RF subsystems like Low Noise Amplifiers (LNA), filters, mixers, etc., as it offers low propagation losses and high-power handling capability. Thus, Waveguide to microstrip transitions have become a major component in millimeter wave systems. Waveguide transitions can be realized using two concepts either by impedance matching or by mode conversion techniques. Inline and Ridge waveguide transition are realized using mode conversion techniques. Aperture coupled and transversal transitions are implemented by applying impedance matching technique.
Choice of waveguide transition technique for implementation depends on the type of applications. Ridge waveguide transitions can be used in applications where low propagation loss is intended. On other hand applications where size is a constraint inline transitions can be better option. Transversal transitions can be used in broadband applications whereas aperture coupled transition can be used where narrow band operation is required
Simple transition from microstrip to waveguide using aperture coupled patch was introduced in 1992 4. Proximity feeding technique is employed for energy coupling between microstrip lines via slot in ground plane to metal patch element placed on an additional substrate. However, experimental results show narrowband performance due to smaller patch length. Aperture coupled transition design does not require back short so application where space is constraint and waveguide is required at backplane of circuit such transition can be used for implementation. Aperture coupled transition offer remarkable advantage in space constraint applications, as it does not require back short.
Transition design for W band frequencies has been presented5 where increase in bandwidth is achieved by moving patch element into waveguide wall resulting increase in distance from feed point. Whereas drawback of this design it added complexity in fabrication and assembly of transition. Based on the experimental results of design presented in6 shows the presence of EM (Electromagnetic) radiation on top of circuit which in turn reduces coupling of energy between microstrip line and waveguide. This is the major drawback of aperture coupled waveguide transition which occurs due to bidirectional nature of radiation propagating from slot aperture. Back radiations can be reduced by using slot in ground plane of microstrip in order to couple energy between microstrip line and waveguide as presented in 7. In this design an additional second substrate with certain thickness covers aperture inside the waveguide and it works as quarter wave transformer for matching impedance between waveguide and microstrip line. Experimental results presented in this paper show reduction in back side radiations. Another approach presented in8 to reduce back side radiation is using CPW (Coplanar Waveguide) instead of microstrip line. From experimental results it can be seen that reduction in backside radiation occurs by aligning of feed structure, but the drawback of such design is reduction in pass band and frequency shift.
Designing of rectangular waveguide transition at higher frequency, mechanical tolerances becomes an issue. In such scenario, transition should consist of minimum parts and preferably a single substrate in order to make transition design more robust against fabrication and assembly tolerances. Design presented in9 provides solution to few of these aspects by analyzing coupling mechanism between patch element and microstrip line. Similar approach has been presented in this present article where coupling mechanism has been exploited using cavity model for patch antenna using matching element. Simulations have been carried out to optimize the patch element length that controls generation of higher modes.
Another technique10 where one side of substrate cover the cross section of waveguide and other side of substrate slot has been defined, coupling between waveguide and microstrip line is employed using quarter wave transformer as a matching element.
This structure offers benefits of easy fabrication and hermiticity. However, the design measurement results show resonating mode. One of the reasons was alumina substrate with high dielectric constant causes resonance. Thus, the transition design presented in this article is designed using duroid substrate that has a lower dielectric constant.
Sensitivity analysis on manufacturing tolerance is presented in 11. Results show that radiating slots and misalignment with waveguide center line are reason for reduction in energy coupling and errors in quarter wave transformer line causes impedance mismatch. Based on this study, simulations were carried out for optimizing various parameters affecting the performance of the transition that has been discussed in section 4 of this article.
An improved version of slot coupling was presented in 12, where a half wave transformer resonant slot aperture couples energy between waveguide and microstrip by shielding with periodic structure to suppress backside radiation from slot in offer to avoid coupling of parallel modes by cap packaging. Design shows improved performance but increases manufacturing complexity.
Article presented in13 shows inline microstrip to waveguide transition based on chebyshev transformer implemented in gap waveguide technology. But the issue with the design is fabrication errors can cause propagation of higher modes. SIW to microstrip transition is presented using LTCC technology14 in which broadband response has been achieved using matching element. But experimental results show higher radiation which causes low energy coupling which in turn causes higher insertion loss.
Gap waveguide-based design has been presented15 to eliminate higher modes by using bed of nails. Drawback of such design is waveguide height lower than 0.6 mm can only be used otherwise second order modes propagation may occur. To address this issue design has been modified by adding ridge to suppress higher order modes. Design presented in16 shows transversal transition design for sub-millimeter frequencies where higher mode suppression along microstrip line has been done by designing structure for shielding. Design presented is simple and easy to fabricate. Aperture coupled transition has been presented in 17. High coupling has been achieved using quarter wave transformer line from center of aperture. However, the drawback of this design is size of aperture needs to be very small in order to avoid the coupling of higher modes between SIW and microstrip line. Transversal transition with new impedance transformer structure has been proposed in 18. Higher flexibility in matching is offered due to transformer element but drawback of design is that performance highly depends on fabrication tolerances.
Based on the above study transition design presented in this letter addresses major drawbacks of aperture coupled transition those are backside radiation and higher modes propagation. Therefore, transition is designed using a matching element and quarter wave transformer line which is used as matching impedance between waveguide and microstrip line. Moreover, the transition structure is simple and compatible with conventional low-cost PCB process. For demonstration of this work a prototype of back-to-back waveguide transition is implemented and measured. The measurement results show good agreement with simulated results.
Design and numerical investigation
Design presented in this paper is a proximity coupled waveguide transition. Entire transition has been designed on a single substrate and substrate is attached to waveguide. Such waveguide transitions are easy to fabricate and assemble. The conductor pattern consists of a patch on bottom layer of the transition and probe at the upper side of dielectric substrate. Dielectric substrate used for design is RT5880 with dielectric constant 2.2 and loss tangent of 1E-04. Substrate thickness 0.254 mm. Rectangular patch on the lower side is surrounded by grounding vias. Aperture is surrounded by grounding via to connect surrounding ground and waveguide short electrically.
The microstrip line acting as probe is inserted into the waveguide. Probe with length Ɩ is inserted and it overlaps the round patch as shown in Figure 1. Mode conversion from Quasi TEM to TE is shown in Figure 2. Microstrip line supports Quasi TEM mode and waveguide supports TE10 mode. Low loss waveguide transitions can be realized utilizing highly efficient TM10 mode as intermediate mode which means mode conversion from Quasi TEM to TM10 followed by mode conversion from TM10 to TE10. Such transition can be achieved using rectangular patch element as rectangular patch which supports TM10 mode. Length of Probe inserted acting as a matching element controls the frequency at which TM01 mode resonates. Back-to-Back configuration for waveguide transition is shown in Figure 3. Vias have been used in order to prevent backside radiation and prevent lateral radiation leakage. The basic characteristics of aperture coupled transition is that they have a narrow operating band which is quite advantageous in few applications.
Detailed parameter for aperture coupled transition
Mode conversion for waveguide transition
Back to back configuration for waveguide transition
Optimization of Bandwidth
Various parameters of waveguide transition were investigated in order to find the optimizing parameter for bandwidth. Cavity model used for patch antennas and dyadic Green’s model for waveguide is shown in Figure 4. L and W are the effective length and width of patch respectively.
Aperture coupled waveguide to microstrip transition
The quality factor Qe for patch element can be given by:
1Qe=1Qwg+1Qc+1Qd
where Qwg is quality factor power transmitter into the waveguideQc is quality factor of conductor lossesQd is quality factor of dielectric losses
Quality factor of Qwg as per cavity model and dyadic model can be given as follows 8
Qwg=15ωπε0εeL2*W*t11-λg2a21sinWeπ2aWeπ2a2
Where ω is angular frequencyε0 is absolute Permittivityλg is guided wavelength
Maximum bandwidth can be calculated by relation between quality factor Qe and effective width W which can be stated in equation (3)
W=2acπ
Where c is a constant value 1.666
For minimum quality factory Qe , Qwg can be calculated as follows
Qwg∣w=2aCπ=15ωπε0εeL*b4t11-λg2a2C(sinc)2
The bandwidth increases with increasing value of a, while effective width W is kept constant if broad bandwidth is required.
Based on above equations it can be concluded that broadband response can be achieved by increasing the relative permittivity εe and substrate thickness. Design presented in this paper was optimized for narrow band performance. Thus, thinner substrate with low relative permittivity has been selected for the design.
Design of transition is done using High Frequency Structure Simulator (HFSS) full wave EM simulator. Simulated results show return loss better than 15 dB and insertion loss less than 2 dB over the frequency band of 34-36 GHz as shown in Figure 5.
Transmission characteristics of waveguide to microstrip transition
Optimization
Bandwidth of aperture coupled transition depends on various design parameters like length of broad wall and narrow wall, substrate thickness, permittivity and patch length. If the length of broad wall is increased, bandwidth increases while conversely increasing the length of narrow wall causes reduction in bandwidth. Bandwidth of design greatly depends on substrate characteristics like permittivity and thickness of substrate. Narrowband response can be achieved with thin substrate and lower permittivity. Selection of substrate thickness and permittivity has been done considering the design development for narrowband response and therefore is designed with RT5880 duroid substrate with thickness 0.254 mm and permittivity 2.2.
Lower resonant frequency of waveguide transition depends on length of patch. Lower resonant frequency can be controlled by length of patch element as shown in Figure 6. Data in Table 1 depicts that the length of patch element does not affect the bandwidth of transition. So if lower modes are to be eliminated than decreasing the length of patch element can help to reduce propagation of lower modes and is shown in Figure 6. Lower patch length higher the resonating frequency. On other hand higher resonant frequency depends on distance between via and broad wall of waveguide. Thus, higher resonant frequency can be controlled using the distance between via and broad wall of waveguide. As the space between via and broad wall increases, resonating frequency shifts towards higher frequencies as shown in Figure 7.
Relationship between bandwidth and transition parameters
Parameters
Bandwidth
Effective width W of patch element
W= 2acπ
Maximum bandwidth
Waveguide broad wall a
Increased
Increases
Permittivity
Decreased
Increases
Waveguide narrow wall b
Decreased
Increases
Substrate Thickness t
Increased
Increases
Patch length L
Fixed ʎ/2
No effect
Return loss versus length of patch element variation
Return loss versus variation in distance between via and broad wall of waveguide
Impedance Matching
Impedance matching can be done by inserting microstrip line within rectangular patch. Insertion of probe inside the rectangular waveguide causes reduction in capacitance and increase in inductance between probe and waveguide wall as shown in Figure 8. Another parameter that can be used for impedance matching is W width of patch element. Resistance can be varied by varying length of patch element. Increase in width causes reduction in resistance as shown in Figure 9.
Smith chart showing variation of probe length
Smith chart showing variation of width of rectangular patch
Fabrication and Measurement
Transition design presented in this paper was fabricated as shown in Figure 10. Figure 10(a) shows the upper plane of substrate and Figure 10(b) shows the lower section of substrate. Size of transition fabricated is 15 mm × 9 mm. Measurements were carried out using N5244 B keysight microwave network analyzer. Comparison of measured and simulated results is shown in Figure 11, Figure 12. Good alignment between simulation results and simulation results is observed. The measured return loss for fabricated transition is better than 25 dB and insertion loss less than 1 dB over a frequency band of 34 to 36 GHz. Surface roughness and fabrication errors resulted in slight discrepancy between simulated and measured insertion loss. Such a superior performance of design is achieved by combination of optimum rectangular patch element width which suppresses higher modes and the probe length being inserted inside the waveguide which increases coupling between microstip line and waveguide.
(a) Upper plane of substrate (b) Lower plane of substrate
Simulated versus measured results for return loss
Simulated versus measured results for Insertion Loss
Comparison
Structural characteristics and performance of various reported articles has been summarized in Table 2. Design presented in19 shows broadband performance compared to design in presented in this article as wedge shaped cavity increases the coupling between microstrip line and waveguide. Design presented in20 shows superior performance in terms of bandwidth compared to present design as higher coupling is achieved as VM strip and aperture together act as ideal transformer and improved coupling efficiency. Present work shows better performance compared to design presented in21 in terms of return loss performance. Transition design presented in22 shows comparatively high insertion loss than present design as coupling between waveguide and microstrip line could be maximized if two slots are placed very near to each other but due to fabrication constraint minimum insertion loss achieved was -4.5 dB. Design presented in [25] shows superior performance than present design in terms of loss as metallized groove technique is used around sidewalls of the rectangular waveguide. Present design shows much lower loss and improved coupling as compared to design presented in [26] over the same bandwidth. Based on comparison with previously reported design, present work considerably shows improved performance in terms of bandwidth, return loss and insertion loss.
Comparison of present work with previous works
Reference
Frequency (GHz)
Substrate Thickness (mm)
Substrate ɛ
Insertion Loss (dB)
Return Loss (dB)
FBW (%)
23
28-38
0.254
2.2
0.8
13
30.3
24
7-13
0.35
10.2
0.82
Better than 16 dB
37
19
47.6-76.7
0.508
2.94
Less than 1.3 dB
Better than 12 dB
44.8
20
57-82.7
0.254
2.2
Less than 5 dB
Less than 10 dB
37.7
21
26.65-30.20
0.254
2.33
0.3 dB
Better than 20 dB
12
22
50-70
0.254
5.8
1.9
Better than 10 dB
8.3
Present work
33.5-38
0.254
2.2
Less than 1 dB
Better than 25 dB
14.4
Conclusion
Design of waveguide transition presented in this study can be used for narrow and wideband applications by varying the design parameters. Optimum width of rectangular patch element for narrowband response has been proposed. Suppression of higher modes generated has also been proposed by optimizing the distance between via and broad wall of waveguide. Optimum combination of patch width and spacing between via and broad wall leads to such improved performance. Simulation and measured results show that such low loss transition can be used practically and can be easily fabricated. Measured results for fabricated design show return loss better than 25 dB and insertion loss less than 1 dB over a frequency band of 34-36 GHz for back-to-back waveguide transition.
ReferencesAppleby RogerCowardPeter RSinclairGordon NTerahertz detection of illegal objects2007Springer225240https://doi.org/10.1007/978-1-4020-6503-3CowardPeter RApplebyRogerDevelopment of an illumination chamber for indoor millimeter-wave imaging2003International Society for Optics and Photonics5461http://doi.org/10.1117/12.487031GraauwTH DeHelmichF PPhillipsT GStutzkiJCauxEWhybornN DDielemanPThe Herschel-heterodyne instrument for the far-infrared (HIFI)2010518http://doi.org/10.1051/0004-6361/201014698GrabherrWMenzelWA New Transition from Microstrip Line to Rectangular Waveguide22nd European Microwave Conference1992https://doi.org/10.1109/euma.1992.335862 GrabherrWHuderW G BMenzelWMicrostrip to waveguide transition compatible with MM-wave integrated circuits1994429184218430018-9480Institute of Electrical and Electronics Engineers (IEEE)https://dx.doi.org/10.1109/22.310597ShireenRShi ShouyuanYao PengSchuetzC AMacarioJPratherD WCPW to rectangular waveguide transition on an ${\hbox{LiNbO}}_{3}$ substrate2009576149414990018-9480, 1557-9670Institute of Electrical and Electronics Engineers (IEEE)https://dx.doi.org/10.1109/tmtt.2009.2020673HyvonenLHujanenAA compact MMIC-compatible microstrip to waveguide transition1996https://doi.org/10.1109/mwsym.1996.511077 SimonWWerthenMWolffIA novel coplanar transmission line to rectangular waveguide transition1998https://doi.org/10.1109/mwsym.1998.689369 IizukaHideoWatanabeToshiakiSatoKazuoNishikawaKunitoshiMillimeter-wave microstrip line to waveguide transition fabricated on a single layer dielectric substrate200285611691177IizukaHideoSakakibaraKunioKikumaNobuyoshiMillimeter-Wave transition from waveguide to two microstrip lines using rectangular patch element20075558999050018-9480Institute of Electrical and Electronics Engineers (IEEE)https://dx.doi.org/10.1109/tmtt.2007.895139CavannaTFranzeseELimitiEPelosiGSelleriSSurianiAFEM-based evaluation of manufacturing tolerances on a millimeter-waves rectangular to coplanar waveguide transition15th International Conference on Microwaves, Radar and Wireless Communications IEEEhttps://doi.org/10.1109/mikon.2004.1356894 PoprawaFZiroffAEllingerFA Novel Approach for a Periodic Structure Shielded Microstrip Line to Rectangular Waveguide Transition2007https://doi.org/10.1109/mwsym.2007.380572 ZhangTLiLZhuZCuiT JA Broadband Planar Balun Using Aperture-Coupled Microstrip-to-SIW Transition201913https://doi.org/10.1109/lmwc.2019.2922499 YakovlevA BOrtizSOzkarMMortazawiASteerM BA waveguide-based aperture-coupled patch amplifier array-full-wave system analysis and experimental validation20004812269226990018-9480Institute of Electrical and Electronics Engineers (IEEE)https://dx.doi.org/10.1109/22.899032Pérez-EscuderoJosé M.Torres-GarcíaAlicia E.GonzaloRamónEderraIñigoA gap waveguide-based compact rectangular waveguide to a packaged microstrip inline transition202010142076-3417MDPI AGhttps://dx.doi.org/10.3390/app10144979VidhiRavalPatelAmitNovel Design of waveguide to Microstrip Transition at Millimeter -Wave Frequencies2020290466456665ZhangTLiLZhuZCuiT JA Broadband Planar Balun Using Aperture-Coupled Microstrip-to-SIW Transition201913https://doi.org/10.1109/lmwc.2019.2922499 XuWLiuFXuHA novel ultra-wideband waveguide-to-microstrip transition for millimeter-wave applications2016610https://doi.org/10.1063/1.4964492 MohamedIssaSebakAbdel RazikBroadband transition of substrate-integrated waveguide-to-air-filled rectangular waveguide201828119669681531-1309, 1558-1764Institute of Electrical and Electronics Engineers (IEEE)https://dx.doi.org/10.1109/lmwc.2018.2871330AliakbarianHadiEnayatiAminVandenboschGuy A ERaedtWalter DeNovel low-cost end-wall microstrip-to-waveguide splitter transition201010175961559-8985EMW Publishinghttps://dx.doi.org/10.2528/pier09081805DeslandesDWuKIntegrated microstrip and rectangular waveguide in planar form200111268701531-1309, 1558-1764Institute of Electrical and Electronics Engineers (IEEE)https://dx.doi.org/10.1109/7260.914305LeeH YJunD SMoonS EKimE KParkJ HParkK HWideband aperture coupled stacked patch type microstrip to waveguide transition for V-band2006https://doi.org/10.1109/apmc.2006.4429440 KimY JKwakJ HSongHJiangXKimJ PBroadband aperture-coupled microstrip line to waveguide transition with loading a vertically mounted strip2017594811815https://doi.org/10.1002/mop.30403 LiC LJinCMaH QShiX WAn inline waveguide-to-microstrip transition for wideband millimeter-wave applications2019https://doi.org/10.1002/mop.32199